Jump to content
Please check your junk folder for registration emails ×

dilly

General Member
  • Posts

    186
  • Joined

  • Last visited

Personal Information

  • Location
    Auckland - North Shore

Recent Profile Visitors

1,007 profile views

dilly's Achievements

Full License

Full License (3/7)

2

Reputation

  1. Aftermarket wheels that arent hub centric or diff/axle as previously said. When did this begin? swapping front to rear will eliminate tyres/wheels if it continues.
  2. Alignment causing vibration? hahaha : yeah nah. Id be getting your wheels/tyres checked by a tyre shop and if its not that its something mechanical as mentioned above.
  3. Stupid taxi drivers... ramble, ramble... Hows your car?
  4. Looks like a combination of under inflation, shit alignment (as said above)and shit quality tyres. I run 40psi minimum in my shitty sagitars to stop that from happening (215/40-17) they looove collapsing right where the steel belt ends.
  5. Agreed. It does look a little rough. If you do want something a little different have a look at this; http://www.autobody101.com/forums/viewtopic.php?f=12&t=18325&start=0 http://www.autogeekonline.net/forum/auto-detailing-101/19023-marble-wrinkle-effect-pics-inside.html my 2c
  6. My 96 250T front sunroof if fixed rear ones goes back and forth + up and down
  7. Ended up doing exactly this after a bit of troubleshooting cause it still wouldn't start I did notice the dash lights dimmed when I did try crank it which obviously ment the battery was under load. Ended up having a shot starter solinoid aswell! I will try (once again) to start it tonight.. it should go tho ;D Thanks for the help guys Ill let you know how it goes.
  8. So just cut wires and join them to 'delete/bypass' the park switch? Have I really over thought it this much :-[ I will try tonight. Thanks heaps in advance.
  9. If you rev the engine from the throttle body does it get louder as you release the throttle? power drill sound is normally a turbo saying goodbye.
  10. The nuetral switch is located at the back of the transmission (inside). I have already grounded the steering lock switch(by the lever). The biggest problem is beacause the transmission is obviously not pluged in the tcu isnt getting power so the lights on the dash (PNRD123) dont light up as theres no power/signal. If I can find the correct wire at the ecu I can ground it so it gets 5v and it will then think its in nuetral. Is the 250t automatic trans loom wiring the same as the turbo model legacy? or even n/a 2.0l + 2.2l Im pretty sure i can splice the neutral switch wire together there to permanantly complete the circut. To be fair, I have no idea what im doing really haha :-[ It took a night to do the full mechanical conversion and its gonna take a week to start the car HAHA! ;D
  11. I did the EXACT same thing doing a manual conversion on the weekend : EXCEPT my mate saw it in there (before we tried starting it I might add) luckily after some fishing with wire/screwdriver and blu-tac we got it out. It should come right once you pull the gearbox off. Good luck
  12. Hey guys, I have recently put a manual box etc into my auto 250t, all went well untill I tried finding an ECU pinout (U9 ECU) so I could ground the nuetral switch so It thinks its in nuetral so it will start. After extensive searching I have found out pinouts for this ecu almost dont exist. I have found 4-5 pinouts with same plug BUT they are for different engines and the pinouts all vary alot. And ones in japanese Im at the point where im gonna need to trace wires back from A/T harness the only problem, I dont know how to use a volt meter. Anyone have any Ideas or suggestions to help? Also, If you do know how to fix the issue im happy to pay. Im based on the North shore, auckland.
  13. Vf13 and Vf 14 come on the 93-95 tt leggys. Vf18 and vf19 on the 'B' spec 96 - 98 and Vf 26 - 27 (i think)on the be/bh. Something seems odd ???
  14. Any signwriting shop will do it in any font/colour/size. They normally dont charge to much either. Just google signwriters and get some prices?
  15. Ive allways used Engine Specialties on Hillside road in Glenfield on the shore. I normally deal with David. They use a diamond tip for machining. All there work is absolutely top notch and they know there stuff! I assembled my own block but they did EVERYTHING else. As allways, you pay for what you get. and if you want 300kw you want it done right.. the first time My 2c anyway..
×
×
  • Create New...