Jump to content
Please check your junk folder for registration emails ×

Andy_Mac

Admin
  • Posts

    5,213
  • Joined

  • Last visited

  • Days Won

    174

Everything posted by Andy_Mac

  1. Have you got a obd2 cable? Have you checked if there are any codes active for the trans. I've had a quick gander through the service manual but couldn't find anything regarding the flashing line where the gear could be.
  2. 190mm like the STI’s on the tbSTI setups, it would be worth confirming beforehand if you can’t confirm it’s a legit tbSTI and not a retrofit. You need rotors that fit a V7 STI if it is for sure complete tbSTI setup
  3. I might know someone with one available, I’ll let you know if he is selling
  4. I’d assume that’s a ripoff AliExpress version which is a risky purchase as the flash going wrong will brick the ecu which is a major
  5. It's a monster task on these cars. To get it to work properly you really need a donor vehicle to swap everything over or you’ll be stuck dealing with random canbus errors and the cost re-syncing everything together.
  6. Pretty sure the facelifts need the tactrix cable as the vehicle type for connecting to ecuflash is ‘subaru can’ which the cheap cables don't support.
  7. It really isn’t that bad to pull them and put them back in. I did mine a few weeks back on a sloping driveway which added some challenges but I still got through it in a couple of hours.
  8. Mine came pre-cross threaded by the last owner. It was a pricey balls up to fix too as they needed to cut the box section open to weld on a bolt. I normally have a big flathead in the opposite side one to maneuver the crossmember into place to get the first bolt in then the second one usually requires a pry bar to get it all lined up.
  9. Have a look at the tomei version. They seem confident in their design not losing much performance while giving a more Subaru sound while just lengthening the two pipes on one side without any rerouted pipes
  10. Interested to see how this performs. The Tomei UEL ones for the FA engine look alright but everyone just rips on them for the inefficiency of the idea without really testing them.
  11. Remove all restrictor pills with a 3-port. Right hand port to atmo, middle to comp cover and left one to the wastegate
  12. I’ve got the 5.0 version It seems to be more than fast enough for how often I use it. I also got it with the rubber bumper case and the battery sense module which helps a bunch by notifying me when it's starting to get low.
  13. The 2.5 non turbo’s are usually single cam (per side). You can tell looking at the front of the engine whether the black covers on the front have two big bulges or one at each end
  14. Also someone like Harley Warwick on FB who wrecks subies will have them available for various vehicles at better than normal wrecker prices.
  15. A GR impreza crosstrek/xv whichever one it was at that point would probably be the closest since the forester chassis is usually closer to an impreza than a legacy
  16. Chuck your vehicle model into japanparts or somewhere like really sport direct and see what that spits out. There must surely be a few options for moderate drop they have. https://www.japanparts.com/parts/list/?dealer_id=1&carmodel_id=136&partsmiddle_id=26&partssmall_id=159&partsmaker_id=&cm_kwd=&carmaker=1
  17. It's still on Facebook at 85k also. I assume you're talking about crashing it at a race event where insurance is a iffy thing?
  18. I think Niran is still trying to unload his one in the more traditional WRB for high 80’s
  19. Very good question. I've trying to find the same answer for my fully stock one with 110kkm on the clock. Harley apparently sells them for 3-4k usually for a semi bare timed longblock.
  20. They still got the GD gen for WRX’s didn't they? Which would make this by that logic the 4th gen.
  21. I guess you could try anyway. The only issue I can think of is without a load correction resistor some led bulbs can stay slightly lit when off but that's with 240v AC stuff, I'm not sure what would happen with 12v DC. Is it the brightness or colour you want to change them for?
  22. Jaycar will have something that fits that profile. https://www.jaycar.co.nz/components-electromechanical/optoelectronics-leds-and-lighting-/leds/c/2EA?sort=popularity-desc&q
  23. Yeah not entirely sure on that. It isn't even really the 3rd gen since it became a standalone model which kind of came about with the VA chassis, with the GR still having the same basic body as the Impreza which just moved to a new body way earlier than the WRX/STI. Depending on how the sheetmetal is made behind it there is potential for quick swap moderate flares that actually match the body unlike 95% of current kits out there though.
  24. As always it's a controversial look that splits people somewhat down the middle, with the majority seemingly disliking it initially but for the most part I quite like it. The front, side and interior are quite nice but the rear end lower plastic piece is a bit weird with the extra depth compared to the rest of the body. Some form of semi functional diffuser on the STI might make it look a bit nicer but I doubt they'll change anything. https://www.google.co.nz/amp/s/www.caranddriver.com/news/amp37281384/2022-subaru-wrx-specs-revealed/
×
×
  • Create New...