Dre
General Member-
Posts
280 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Events
Store
Everything posted by Dre
-
I think RSS have been involved previously with the MCA gold series range as the owner races off road.
-
Limited stock just arrived.I don’t think prices have been worked out yet.I was more interested in build quality.
-
Street Ultimate Aus $2750 / NZ $3250 (estimate).
-
Was given a estimate,Aus dollars retail converted to NZ dollars.RSS also revalve and rebuild them.
-
Dropped in to see my local suspension guy at Race Shock Specialist,Penrose.They are now the NZ distributor for MCA Suspenion.They currently have a small range in stock.
-
BM BR Exhaust - Anyone have stock dual mufflers that I can buy?
Dre replied to nsh's topic in Legacy & Outback
Two sets on Tm at the moment,17” and 18”. -
My favourite.Could I stance my car so the new tyre labels don’t wear.
-
I’m sure your Td04 can be rebuilt and modded but not sure about the Vf38,44 and 45.@Andy_Mac the Td04 ‘maybe’ has the larger compressor wheel.Was told by my tuner that the Vf45 flows the best top end.@Mikk Wreckers price on a used Vf45 approx $650.Check out Kinugawa Legacy twin scroll turbos for new aftermarket.
-
Vf38,vf44 and Vf45 are the only direct replacements.Vf45 being the best.Limited choice of turbos for the 2.0L twin scroll Legacy.
-
I had a car that had same problem.Didn’t replace the spigot bearing in the crankshaft after engine came back from a rebuild.You can also damage the bearing if the clutch plate isn’t aligned properly when installing the gearbox.It’s a cheap part which is generally overlooked.
-
Front side cam cover below oil dip stick.4 x 10mm bolts.I have a mini Teng tools socket set 5.5 to 13mm sockets,various screw heads,extension and ratchet.All packaged in the size of a cigarette pack.Cost around $65. TengTools BBX20
-
Listen for any nasty rattles or noise coming from cam covers and remove passenger side cover and check cam belt for wear and cracks.Purchased my bl in Nelson and drove back to Auckland with barely legal S*** tyres.Wellington to Auckland was in pouring rain and darkness.Bent a rim driving through Hamilton.
-
My old Bh tt didn’t have a vacuum leak,but because the vacuum reservoir hoses were pinched the reservoir couldn’t reach full vacuum,causing intermittent sync problems between the twin turbos.No check engine lights.Was suggested by a good Subaru mechanic to check vacuum hoses,especially the plastic pipe/hose that runs from the reservoir around the front of the radiator to the solenoid box.Maybe a small vacuum leak causing the reservoir to loose vacuum overnight.As soon as car started,vacuum replaced.These cars are getting old and require a lot of maintenance because of the complexity of the tt engine.Cheap to buy,expensive or time consuming to maintain. My old Bh tt will make full boost from cold.I’m always telling my son to warm the car up first.
-
Possibly a vacuum leak that stops the vacuum reservoir in the passenger front guard holding vacuum which controls the tt solenoid box which controls the turbos.Had this problem after a engine rebuild where the tards had trapped/pinched the vacuum hoses to the vacuum reservoir under the battery.
-
Outback 3.0 - can it TOW 2 tonne tandem trailer?
Dre replied to Aptenodytes's topic in General Vehicle Discussion
I have a 3.0 Outback facelift and agree with poor fuel consumption.I normally use the white Subaru oem filter but replaced the air filter with the orange type,noticeable improvement in fuel consumption.Run Mobil 98 from the same local gas station. -
Thank’s @pedro and @Bobby.Working on a budget at the moment.I was looking at pulling Legacy engine but will have to stay in car for now.I’m concentrating on oil surge and cooling first.RCM baffled sump,pick up and SAS baffle plate on it’s way.Looking at oil coolers now.RCM will probably be my first choice.Got to keep some funds available as I’m waiting for Michelin to have a sale.
-
4 & R North Island Jamboree 10th year Anniversary! Manfeild March 23/24 2019
Dre replied to Joker's topic in Club Events
Forget the spare wheel,weld on a big rear wing and don’t forget the baked bean can muffler tip. -
I tried this with a single turbo conversion into a 94 Legacy Rs tt early 2000.Car ran fine,but once boost exceeded primary turbo tt boost ecu switched to limp mode.Might be different with your the later model tt ecu,but still requires a lot of work to the solenoid box.Eventually wired in a aftermarket ecu,removed the solenoid box and was able to make changes to ignition timing and fuelling.
-
What let’s go first on a Sti V7 short block,bearings,crank,rods or pistons.
-
Legacy BP5 Subtech Downpipe Rubbing Steering Column
Dre replied to RepNZ's topic in General Vehicle Discussion
If you lower your car excessively it can place additional strain on the inner cv’s.I’ve seen some front axles on a Legacy bp made for this purpose.I’m sure Supergramps blew one side only. -
Doesn’t mean they own it.Unfortunatly when you purchase privately,if you have any concerns regarding the sale list it in the receipt of sale and make sure it is dated and signed by the seller.In court it will be your word against there’s.
- 29 replies
-
- 3
-
Small claims court is a waste of time.If you win,the defence can claim poverty and ‘dribble out payment over years.Payment is not enforced.
- 29 replies
-
- 1
-
Give ADL Autoparts a call regarding rebuild of your driveshaft to see if it can be rebuilt.Hard to find good second hand parts for gc8’s now.
-
Join HP Academy if you want to build your engine properly or get a better understanding of how a performance/race engine should be built.Excellent modules take you through preparation,measuring,machining,clearances,balancing,blueprinting and assembly.
- 85 replies
-
- 3
-
- engine build
- ej20
-
(and 4 more)
Tagged with:
-
Sti and sedan guards are the same for V7.
-
Who's Online 0 Members, 1 Anonymous, 67 Guests (See full list)
- There are no registered users currently online