Jump to content
Please check your junk folder for registration emails ×

bc5rs

Christchurch Member
  • Posts

    76
  • Joined

Everything posted by bc5rs

  1. assembled my bottom end and tourqued heads down cleaning manifolds now should go in soon
  2. hey just rebuilt my bottom end went to put cams in and thought i wonder what else could go in here are there any cams i can put in there standard ej20g heads dohc turbo etc i was told ej25 ones might fit i really dont no any help would be helpfull
  3. can I run standard non turbo 2.2 pistons in a turbo application no its not designedforit but worth the question if not I was getting aforge set from the states
  4. mightwant to check timing marks i had a similar incident and it was 1 tooth out
  5. ok just a reminder ive got a bc5 rs-d according to the tags no abs or anything fancy td05 tuned manifold 440cc injectors bosch external with surge tank attached micotech lt8s pluged into factory loom ra front and rear seats 240km speedo ra box rather close ratios ssr type c rims 4 pot fronts lowered just springs before the mods it did a 13.9 on the quarter mile 1evlrs rayburg spotlights hid v3-4 scoop not sure which still got the waic but thatl change building a 2.2 flipped manifold front mount ect clean silver body with the we lip on the kit at the track day i blew some ring lans thanks to a bad lift pump so my 2.2 build is now underway i have my 2.2 block good clean one no damage crank ,using the crank from my cdb rods i am buying from a freind after i strip his engines for him pistons anr only 600 landed from the state bearings are local as luqifaction and caraid have my heads gtb ,and will bolt them on for me after reseating etc im getting a alloy rad but its going to be 3inch shorter so allow the cooler pipes to go over it ( i dont want tocut my chassis) flipped manifold 550cc injectors from another mate and then i havent decided on turbo yet td06 or something of the like anywho just thought i should write it down what i was up to , body wise changing front lower arms and suspention to adjusties maybe some underbody bracing aswell but engine is the item on the go at the moment
  6. stay focused on the topic and less on being a twat logan
  7. i just ripped into mine and same thing my lift pump died so i had not much fuel and bang slowly ,
  8. hey guys ive been offered a v8 short block for 200 done 110km are there any benifits to v 8 or should i stick with my old cdb from the rs ?
  9. pulled engine out,left the box behind was easy as side of the road i shattered #ring lans and nearly cooked a ring >
  10. This sucks s***. One of the times I put engine I did this and ended up getting the 2 bolts undone and pulling it out the bottom in place. Massive mission. Just remember the clutch fork pin it seems to catch out a lot of people. dont have to worry about it when its goin in is when your splitting them the pin needs out because the clutch has a 1 way spring clip once its engaged its a c*#t to get out again in place, mate engine to box first then slide the mounts down and in fairly simple just teadius work dont expect it to take 20 min haha
  11. yeah he hasnt replyed to my emails or calls yet
  12. hey guys who has had good\bad assembly jobs in chch was thinking either car aid or mace ive got 90% of the parts myself just want someone else (with a warranty) to do the torqueing so to speak,dont want a brofessional on it
  13. it makes the differnce in the egr twin cooling trucks because the injectors are very tempermental about what goes through them,for instance a we have to make some trucks relearn there fuel maps to adjust the adblu content in the exhaust du to adblu beingdependant on current exhaustflow ambiant temp pressure etc but either way im still picking its electrical issues hes got
  14. keep in mind hes probably got a better 98 octane than ours in nz we have shit fuel to the point some of our road transport trucks and digger even have to have a extra filter set up to maintain the euro emission standards and not bugger the engines because there tuned on euro fuels (scania-hitachi komatsu-hyundai-mercedes and freightliner all do ,or there fuel filters are nz spec higher filtration level
  15. i if its bacfiring then theres fuel and air id say noones looked at the sparkplugs or coils in as they will break down at temperatures ,my bc5 coils worked fine but i pulled them out and i was amazed at the cracks in them it was impressive replaced them though br worth doing a decent service that way you have a base to compare anything on if the oil in the box for instance is glitery then well thats pretty self explanitory same for the rear diff
  16. Are those rims SSR type C? : yes sir they most certainly are
  17. theres a flexi in the up pipe already i just had the turbo oil feed pipe bend on me and spray nice gold oil over everything i recomend wrappin the up pipe twice for good measure ive had mine for 3 years now ,wrap the othe pipes to just keep in mint that road debris will slowly take it off i made a small sheild on the bc5 for it though , theres no problem with them ive had other than my filter issue
  18. http://www.trademe.co.nz/motors/car-parts-accessories/subaru/other/auction-664887146.htm these are what i have and i rate them had them glowing wrapped them and no problems except manifold gaskets
  19. yeah the fleetgaurd opne is the onlyone that is short enough
  20. i run stainless headers and there a faint hint of rumble at idle but if you wernt looking you wouldnt pick an ej sound like a silvia more though ,anyway mine are from the mcphail group kain was his name only problem i had was oil filter clearance have to use a lf3079 or 3034 cant remember and use real mls gaskets i blew 3 sets of composite ones before i changed them i think it was just the expantion between the alloy and stainless,also beware they can hang low my car isnt very low but the manifold is ,luckily its inbetween the wheel area to dont have to worry much, and brace the up pipe on the factory mounts because of the steel oil feed line doesnt like to flex much i cant find a pic of my ones havent seen another set like them anyway what ones were you looking at?
  21. i run standard trw rotors and havent had a problem took it to the track and dint feel i needed more brakes just keep in mind your oem ones lasted a fuck of alot longer than any after market ones with aftermarket pads COEFFICINCYS and the such
×
×
  • Create New...