Jump to content
Please check your junk folder for registration emails ×

Search the Community

Showing results for tags 'electric'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • General
    • General Vehicle Discussion
    • Stolen Vehicle Register
  • Knowledge Base
    • General FAQ (Read Only)
    • Model Specific Discussion
    • Non Model Specific Discussion
    • Legal
    • Motorsports
    • "Other" Tech Questions
    • Product and service reviews
  • Regions/Events
    • ClubSUB Events
    • Auckland/Northland
    • Waikato / Bay of Plenty / Taupo
    • Taranaki / Whanganui
    • Manawatu / Wairarapa / Hawkes Bay
    • Wellington / Kapiti
    • Nelson Bays/Marlborough
    • Canterbury
    • Otago / Southland
    • Outside NZ
  • Classifieds
    • Car Exchange
    • Parts Exchange
  • ClubSUB Shop
    • ClubSUB Shop

Product Groups

  • Subscriptions
  • CS Clothing
  • Stickers and Decals
  • Subaru Branded items
  • ClubSUB branded items
  • Limited Edition Items

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me


Drives :


Interests


Location


Occupation

Found 2 results

  1. Does the base of your seat feel loose on one side? Does the height adjustment only work on one side? Well, turns out subaru seat bases aren't as strong as they should be, and if you sit on them the wrong way, you'll bust the spot welds off the frame, leading to one side of the front of the seat squab flapping about. Hopefully it broke in a useful spot, otherwise I hope you enjoy being uncomfortable! 😛 Heres how to fix it, you will need; Socket Set 2x small bolts, washers, and nuts Drill + drill bits a bit bigger then the bolt threads Reaming tool Magnetic Pick-up tool Step one, look at this image, everything circled is important Step Two, Remove the seat There are 4x 14mm bolts holding the seat into the car (Circled in RED) you'll have to move the seat back and forward to get to all of them. Once thats done move the seat base as far forward as it can go, and the backrest to straight up to make it easier to remove the seat from the car disconnect the battery. Then disconnect the battery, press the brake pedal to disperse any latent power and you can then tilt the chair forward and disconnect the 2 connectors (circled in GREEN) Then carefully remove the seat from the car and place it on something soft. Step Three, Located your busted welds The two spot welds (location circled in ORANGE) that hold the front of the seat will have busted off on one side (or both if you're REALLY unlucky) Good Weld BAD WELD! Same from above, totally busted Step Four, Fix the weld. The bracket that has busted off, will be part of a assembly that hold the seat in place, and as its busted will be super loose. Every time i've seen it, the metal work holding the seat cushion is left with two nice round holes perfect for putting a bolt through, leaving you with the job of drilling holes in the bracket to match. Do your best to brace the bracket, and drill two new holes. Try to get them as central to the location of the welds as possible, but if you drill larger holes and use washers you can give yourself a bit of leeway Once thats done, use the reaming tool to clear out the left over material from inside the bracket, as if left you'll end up having to squash it when you tighten up the bolts, and as theres no easy access, you may not have enough torque to pull it flat. it'll still work, but you may have to go back and tighten it up again. Use the magnet tool to recover as much metal dust as you can that fell into the seat to save it getting into the mechanisms, and the carpet once you turn it back over. Step Five, Replace the seat You just removed it, do the reverse and you should have a seat in the car bolted down that doesn't flex, and you can now enjoy(?) the feeling of lifted thighs!! Make sure to test the seat through its full range of movement before you bolt it in, as if somethings gone wrong you'll both save having to unbolt it, but also if its loose you may get away with just making a noise rather then snapping something.
  2. Hey guys, Just wondering if anyone can help before I hit up an auto sparkie. The climate control screen in my BP5 Spec B legacy has stopped working, the climate control still works perfectly fine, its just the screen that has gone. The Macintosh system still works fine too. Just wondering if anyone has experienced this and can help me fix it. Cheers!
×
×
  • Create New...