Jump to content
Please check your junk folder for registration emails ×
  • Current Donation Goals

    • Raised $0.00

mind blank...4pot Q?


Recommended Posts

Im upgradeing to 4pots this weekend (as my brakes are creating disk rust! and I cant remeber off the top of my head whether i need to take CV nut off to take disc's off?

if i do have to take taht 32 mm nut off i have to put whole hub assmbly in. is there any difference between hubs wrx vs sti?

Cheers

Link to comment
Share on other sites

done a few now...just had a mind blank...i have complete cv's/hubs/dics etc...just wanted to be sure in case i had to end up swapping hubs over...does anyone knwo if 96 sti spec wheel bearing will be betterer than a 93 wrx...any improvement or did this just change at V7 onwards (bigger bearing)

Link to comment
Share on other sites

Guest boostin
 funkytown']

As Koom said but...

get a BFH... sometimes the rotor sticks onto the hub and needs lossening

[quote name='Swindog said:

you screw two bolts through the hub of the disc and itll pop off. I wouldnt use a BFH. Its loud when you have your head under there.

Always use the bolt method. The BFH one works, but you can't (well, shouldn't) use the discs again.

Link to comment
Share on other sites

she was all done and dusted yesterday, much nicer braking (altho i was down to metal on one side) it feel like there is quite a lot more travel in the pedal, i suspect its cos more fluid needed due to the additional clylander?

Link to comment
Share on other sites

 Swindog said:

must be ok then. Youll feel it better if you get some heat in them. Brake cylinder brace will increase the feel or pump them once or twice as you brake.

yep have only driven it round the block so def no heat in them... no brake cyl brace...yet :P

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Status Updates

    • MrSg9Sti04

      Afternoon team,
      im new to the group first time posting. Im hoping some body can help me get my launch control all dialled in on my link g4x. Ive had the computer and car all tuned from chris at prestige awesome knowlegable guy super happy with the results but now im wanting to get my launch/anti lag all dialled in. Ive been reading multiple different forums etc all with different conflicking information which has made me nervious with what do i listen to this or that if you get what i mean. Now ive started to make myself familiar with my PClink software etc the past few weeks and im eager to learn how to do minor setups or tweaks etc so im not relieing on my tuner so much and obviously saving myself abit hurt in the back pocket. 
      Now back to the question at hand.... Im wondering if theres and one who could please share there knowledge and wisdom with setting all my values, timing, fuel etc when i have launch control armed and engaged, or even a launch tune file they can possibly send me to load onto my tune. Ive figured out the setup of my digital inputs turning launch control on etc and its obvisously on its pre set factory settings. It engages but doesnt sound the greatest or as angry as it should i feel. Hence reaching out to you good buggers. 
       
      Cheers in advance for any info and help yous maybe able to give me.
       
      Cheers Shaun
      · 0 replies
    • Joker  »  gotasuby

      updated your DP's too : hope that's ok!
      · 0 replies
    • Joker  »  SAS

      Updated your DP's to reflect your business page  
      · 0 replies
    • Joker  »  Nachoooo

      Updated your Avatar : couldnt help myself  cheers!
      · 0 replies
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    40.9k
    Total Topics
    573.5k
    Total Posts


×
×
  • Create New...