Jump to content
Please check your junk folder for registration emails ×
  • Current Donation Goals

    • Raised $0.00

New AVCS Issue (V7-on) oil feed


Guest

Recommended Posts

As a few of you are now finding there can be issues with poor performance, rough idle etc that are caused by an issue with the AVCS system

In the below picture you will see the oil feed to the L/H AVCS actuator valve - note my grubby finger pointing to the banjo bolt

AVCSboltlocationLHS.jpg

Inside this banjo bolt is a screen filter for the oil supply to the AVCS valve See pic below

AVCSboltandfilter.jpg

This filter can fall out of the bolt and goes straight into the AVCS valve underneath it, jamming its moduation control for the AVCS system

Causing either full advance, full retard, or no avcs application applied

FIX

Those of you already having issues, remove the banjo bolt (note 2x copper washers) and ease the pipe to the side about 15mm (dont bend the pipe)

remove the basket, by gently easing the AVCS valve (the valve is spring loaded, which is why it holds onto the filter basket)

Once the basket is out, reassemble - refit the banjo bolt with the copper washers x2 correctly under and on top of pipe fitting

Strat engine and check for leaks

Those of you not having a prob yet - remove the bolt and remove the filter basket, reasemble as above

Link to comment
Share on other sites

in the interest of preventing leaks, anyone know the part number for the copper washers? or the correct size to use ? would be just handy to have then before the removal rather than rushing off to find one that fits ;)

Link to comment
Share on other sites

 jpar196 said:

in the interest of preventing leaks, anyone know the part number for the copper washers? or the correct size to use ? would be just handy to have then before the removal rather than rushing off to find one that fits ;)

12mm copper washers. I'll send you some with the sensors next week if your worried

But they are good to re-use no problem at all

Link to comment
Share on other sites

 Muff Slayer said:

Does this issue throw a CEL light?

I have vowed not to fix something unless its broken :-\

This wont throw a code until it blocks the valve modulation and the cam goes to max advance/retard

This is an easy check on most cars ( some you need to loosen the injector cover plate (noise plate)

Link to comment
Share on other sites

 Ichi Ban']

[quote name='jpar196 said:

in the interest of preventing leaks, anyone know the part number for the copper washers? or the correct size to use ? would be just handy to have then before the removal rather than rushing off to find one that fits ;)

/quote]

12mm copper washers. I'll send you some with the sensors next week if your worried

But they are good to re-use no problem at all

I personally replace them,but then I am pedantic at times :)

a quick trick,if you can do it is to heat them up as hot as u can get them(if they glow cherry red then awesome) as this anneals them and then they can seal better :)

Link to comment
Share on other sites

never herd of heating copper washers ? what you can do is if the washer isn't flat any more (worn a groove) You can normally sand them smooth again and they seal perfect. . but normally if you remove them and they look flat and smooth they won't leak . just make sure sealing surfaces are clean

Link to comment
Share on other sites

  • 2 months later...
 Slidesector said:

Is it easy to get to while engines in??

if you have TGV (tumble generator valve or even TGV blanks) they are a mission

but a std manifold = about 30min for me

Link to comment
Share on other sites

 kinggts25 said:

Would this be a cause for bad cold running and hesitation? every other sensor has been changed (almost!)..

cold running issues can be many many things, you'd need to see what the cams are doing when cold with a scan tool

replacing sensors for no reason is a waste of time and money - Well spent diagnostic time = heaps less stress and cheaper repairs

Link to comment
Share on other sites

 Ichi Ban']

[quote name='kinggts25 said:

Would this be a cause for bad cold running and hesitation? every other sensor has been changed (almost!)..

/quote]

cold running issues can be many many things, you'd need to see what the cams are doing when cold with a scan tool

replacing sensors for no reason is a waste of time and money - Well spent diagnostic time = heaps less stress and cheaper repairs

Yeah pity i am up in auckland! I'd love to get it looked at by someone that knows what they are doing! it was the car dealership last time - replaced every sensor, claimed the diagnostics looked fine...dont believe it..

Link to comment
Share on other sites

Hey I think I may be having the same problem, my v7 sti just started shaking rough at idle and kinda sounded like it was misfiring. Thought maybe it needed some new spark plugs but after changing them still have the same problem so maybe its a avsc issue.

Just wondering is the filter supposed to be shoved inside the grub screw quite tightly, I guess so it doesnt fall out? Or is it supposed to be sitting loosely at the base of where the screw screws into?

Any help is appreciated :)

IMG_0770.jpg

IMG_0772.jpg

Link to comment
Share on other sites

 Dangeruss said:

Hey I think I may be having the same problem, my v7 sti just started shaking rough at idle and kinda sounded like it was misfiring. Thought maybe it needed some new spark plugs but after changing them still have the same problem so maybe its a avsc issue.

Just wondering is the filter supposed to be shoved inside the grub screw quite tightly, I guess so it doesnt fall out? Or is it supposed to be sitting loosely at the base of where the screw screws into?

Any help is appreciated :)

IMG_0770.jpg

IMG_0772.jpg

They are a tight fit from factory, and are fitted well into the banjo bolt

Looks like you saved yours in time :)

Link to comment
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Status Updates

    • MrSg9Sti04

      Afternoon team,
      im new to the group first time posting. Im hoping some body can help me get my launch control all dialled in on my link g4x. Ive had the computer and car all tuned from chris at prestige awesome knowlegable guy super happy with the results but now im wanting to get my launch/anti lag all dialled in. Ive been reading multiple different forums etc all with different conflicking information which has made me nervious with what do i listen to this or that if you get what i mean. Now ive started to make myself familiar with my PClink software etc the past few weeks and im eager to learn how to do minor setups or tweaks etc so im not relieing on my tuner so much and obviously saving myself abit hurt in the back pocket. 
      Now back to the question at hand.... Im wondering if theres and one who could please share there knowledge and wisdom with setting all my values, timing, fuel etc when i have launch control armed and engaged, or even a launch tune file they can possibly send me to load onto my tune. Ive figured out the setup of my digital inputs turning launch control on etc and its obvisously on its pre set factory settings. It engages but doesnt sound the greatest or as angry as it should i feel. Hence reaching out to you good buggers. 
       
      Cheers in advance for any info and help yous maybe able to give me.
       
      Cheers Shaun
      · 0 replies
    • Joker  »  gotasuby

      updated your DP's too : hope that's ok!
      · 0 replies
    • Joker  »  SAS

      Updated your DP's to reflect your business page  
      · 0 replies
    • Joker  »  Nachoooo

      Updated your Avatar : couldnt help myself  cheers!
      · 0 replies
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    40.9k
    Total Topics
    573.5k
    Total Posts


×
×
  • Create New...