Jump to content
Please check your junk folder for registration emails ×
  • Current Donation Goals

    • Raised $0.00

Fuel pump not priming after cluster swap


DansSTI

Recommended Posts

Hey guys, new to this forum. So long story, i bought a 2005 uk spec v9 with a blown engine a couple of months ago. Me being me i wasnt happy with how it didnt have dccd and all those other cool features so i bought a complete jdm v8 harness and swapped that into the car (no biggie) after fixing issues of swapping over door actuators and all that other stuff i didnt think about. I go to turn the key to check all the accessorys opperate, windows, doors lights ect. Did i mention i bought a 260km dash out of a s204. With out the cluster plugged in the fuel pump primes, with the cluster in the fuel pump wont primes, obviously its a pinout issue with the cluster. But i wanted to know if anyone has the answer before i start diagnosing (painfull for me since im a fabricator not an electrician lol).

Also, when you go to unlock the car with the key the drivers door will unlock but the rest of the doors wont, if you press the lock/unlock all doors button on the drivers switch panel all the doors will work as they should. The door key lock has 3 wires coming off it but theirs nothing for them to plug into on the 03 loom. Any ideas? 

 

Link to comment
Share on other sites

  • Admin
14 hours ago, DansSTI said:

Hey guys, new to this forum. So long story, i bought a 2005 uk spec v9 with a blown engine a couple of months ago. Me being me i wasnt happy with how it didnt have dccd and all those other cool features so i bought a complete jdm v8 harness and swapped that into the car (no biggie) after fixing issues of swapping over door actuators and all that other stuff i didnt think about. I go to turn the key to check all the accessorys opperate, windows, doors lights ect. Did i mention i bought a 260km dash out of a s204. With out the cluster plugged in the fuel pump primes, with the cluster in the fuel pump wont primes, obviously its a pinout issue with the cluster. But i wanted to know if anyone has the answer before i start diagnosing (painfull for me since im a fabricator not an electrician lol).

Also, when you go to unlock the car with the key the drivers door will unlock but the rest of the doors wont, if you press the lock/unlock all doors button on the drivers switch panel all the doors will work as they should. The door key lock has 3 wires coming off it but theirs nothing for them to plug into on the 03 loom. Any ideas? 

 

 

You may have some more luck with the UK sites, but definitely interesting what you're doing. 

 

When you say V9, do you mean Hawkeye or the mechanically revised blob eye? 

 

The issue I believe you'll be having is down to the difference between pinouts for sure. Interesting that the Fuel pump relay runs through the dash. Doesn't make sense as to why it'd do that.

Link to comment
Share on other sites

58 minutes ago, Dairusire said:

 

You may have some more luck with the UK sites, but definitely interesting what you're doing. 

 

When you say V9, do you mean Hawkeye or the mechanically revised blob eye? 

 

The issue I believe you'll be having is down to the difference between pinouts for sure. Interesting that the Fuel pump relay runs through the dash. Doesn't make sense as to why it'd do that.

Hey thanks for the advice, yeah its a 2005 blob eye, just before the hawkeye, so it has the little rear arch extenders on the rear and those other sort of bits. 

Its a weird issue because i swapped the whole loom over from a jdm v8. If i had the pinouts for both connectors i could figure it out. 

Link to comment
Share on other sites

  • 2 weeks later...

Figured out the issue, turns out the ecu pinouts are different between the jdm and UK. I just had to depin and swap over 6 wires, took me ages to find the two different service manuals. But its pretty simple to swap the pins over.

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

http://ken-gilbert.com/impreza-manuals

https://www.scoobynet.com/general-technical-10/777689-jdm-sti-gdb-ecu-pinouts.html

Heres the link to the manuals and the forum post i followed. I double checked all of the OPs instructions before doing it and traced all the wires back to make sure i didnt fry my link lol. All ive gotta do now is configure the ecu to use the factory spec c iat instead of the one that people use when they splice into the maf sensor temps. Then extend the wires from the watersprayer to the boot and check that works with the manual and auto function. Anyways no more time to work on my car, ive got rally cars to prep for the upcoming season, fab work doesnt get done on a keyboard (and not much time to do so might i add)

Edited by DansSTI
  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Status Updates

    • MrSg9Sti04

      Afternoon team,
      im new to the group first time posting. Im hoping some body can help me get my launch control all dialled in on my link g4x. Ive had the computer and car all tuned from chris at prestige awesome knowlegable guy super happy with the results but now im wanting to get my launch/anti lag all dialled in. Ive been reading multiple different forums etc all with different conflicking information which has made me nervious with what do i listen to this or that if you get what i mean. Now ive started to make myself familiar with my PClink software etc the past few weeks and im eager to learn how to do minor setups or tweaks etc so im not relieing on my tuner so much and obviously saving myself abit hurt in the back pocket. 
      Now back to the question at hand.... Im wondering if theres and one who could please share there knowledge and wisdom with setting all my values, timing, fuel etc when i have launch control armed and engaged, or even a launch tune file they can possibly send me to load onto my tune. Ive figured out the setup of my digital inputs turning launch control on etc and its obvisously on its pre set factory settings. It engages but doesnt sound the greatest or as angry as it should i feel. Hence reaching out to you good buggers. 
       
      Cheers in advance for any info and help yous maybe able to give me.
       
      Cheers Shaun
      · 0 replies
    • Joker  »  gotasuby

      updated your DP's too : hope that's ok!
      · 0 replies
    • Joker  »  SAS

      Updated your DP's to reflect your business page  
      · 0 replies
    • Joker  »  Nachoooo

      Updated your Avatar : couldnt help myself  cheers!
      · 0 replies
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    40.9k
    Total Topics
    573.5k
    Total Posts


×
×
  • Create New...