GC82GO
-
Posts
296 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Store
Posts posted by GC82GO
-
-
I put the 1994 FWD Impreza Steering rack into my RWD GC8 for extra lock.. Also when I did a V7 Engine/Loom conversion into a V2 GF8 I was told we had to use the Rack from the V7, Pulled it out and compared them and they were exactly the same apart from different part numbers. Ended up just using the PS/Lines and PS/Pump from the V7 and the V7 PS/lines fitted perfectly with the 1995 GF8 PS/Rack, So I could imagine most Subaru Impreza steering racks are interchangeable, Definitely V6 RA Rack swapped with a V6 STi Rack, be no problems.
-
Boon, yes I need more camber on the front, prob about 3.5degrees, the rear though can stay with full contact patch...Yes I thought the same, but experiences from drifting my R32 and WRX, Say 16's are the slippery ones. 17's just seemed to give more grip. But its common knowledge at the drift scene, you'll see most underpowered cars running 15's and 16's at the drift days.. So has anyone tested 16's on Brembo 2Pots before?
-
-
Hi there, Im looking at installing some Brembo brakes onto my RWD built GC8, just wanting to know if anyone has tried fitting a 16" rim on the rear with the Brembo 2 pot calipers, Ill be running 17x8 WORK CR Kai's in the front so no problem there. I do have a barrage of 17's I could run in the rear but I'm worried about the rear axels snapping (already had 7 axles snap mid drift), Im upgrading to some 900HP axels and a 900hp Rear Spool for the R180 Diff soonish (as funds allow). I would try test some 16's on my V3 STi RA which has brembos installed already but I live on a hill and my motor is blown (Replacing this weeknd with another V3 STi Motor) so I cant jack it up saftely.. No problems if it doesn't fit, just thought be nice to have good brakes on my hack.
-
Cheers I also seen it, it's algood it shouldn't be hard to figure out I hope, I'm thinking 1 and 3 go together and 2 and 4... And the ground isn't used anymore.
-
Hi all, just in the process of putting a v5 motor into my rwd Wrx which is a ver 3. Is anyone able to tell me which wires need to be paired together at the igniter plug as I won't need to run the v3 ignitor.
Thanks
-
Hi all im looking at purchasing a motor and the guy claims it to be out of a version 4 Sti, what I'm wanting to know is can you put the ver1-2 camshaft covers onto ver 3-4 heads. Anyway of telling from looking at the heads to know what the heads are..
Thanks
-
Didn't end up compression testing it.. But I ended up fixing the speedo and found my O2 sensor was unplugged from doing my flywheel/clutch/box so it's all go now! I brought a v2 RA gearbox and 3.9 ratio r180 diff and put them in when I changed my clutch and flywheel, also swapped the transfer cases over so I still have the dccd. More issues arise though, I have a worn valve stem seal or 2.. the Motor will come out soon to repair that..
-
Ok that's good to hear thanks kamineko. Also I been reading I might be running too much fuel pressure, its set at 43psi at idle.. But I just read that it needs to be set with the Vac line to the FPR off... then with it on it should sit around 32-36psi. But I guess that's a different thread....
-
Also there is a lot of black carbon deposits all over my rear bumper near the exhaust.. I will compression test the motor tonight.
-
This is another random note about what was affected after my Flywheel/Clutch Change/gearbox change. My car was running more boost after the change. was reaching 1.3-4 bar when I had my boost controller set to .9 bar. I lowered the Duty Cycle and this brought it back down, but I didn't notice it until last night. So have done a few hard pulls on 1.4 bar... Possibly my motor is hurt? as it smells like a lot of gas and a tiny bit of smoke will come from the exhaust when I rev it on the spot to about 6-7k RPM... Dtech said this was fine but needs the Fuel mixture checked.. I don't know tho. I thought smoke coming out of the exhaust was oil burning?
-
Ahh yes I will make a ground up and install it on the gearbox connecting to the firewall. Actually no... my speedo is not working, Will be fixing that today, do you know what problems this can cause?
-
Will check the o2 sensor soon, Just went to Dtech, didn't seem like anything to worry about but my fuel pressure of 3 bar is too much the guy reckons.
-
Yea could well be electrical issue, Is there is meant to be a earth from the gearbox to the body? If so my car is missing that. I Didn't think to check the plugs, I mean she boosts fine. But I can smell gas... Im gonna take it to Dtech at lunchtime.
-
Hi all, purchased a HD Clutch/Pressure plate and Lightweight flywheel, Installed them this weekend that just past, and now im having a world of troubles. She wont Idle properly, getting a CEL coming up randomly but not all the time, and now she is backfiring a lot more than normal even under casual nana driving. and when I rev it up on the spot she starts smoking out the back and smells like gas!.. all started since I put the Clutch/flywheel combo in, anyone had similar issues.
-
The one Rosssub put up is the best id say. Has the pinout differences that the Immobilised and non Immobilised versions of the JDM V7 WRX/STi with AUTO and Manual Also.
-
Great, finally started it, after rechecking the wiring, found it was just a dodgy coil power wire merge lol.. Fixed that, fired up straight away. No cel codes so far, just need top up the water and check if the fans will turn on when she gets over temp and see if any problems arise. Not so afraid of this loom conversion now!
-
But both sensors need to be wrecked right, I just tested on my V3 STi RA which has the factory 6S ECU, I unplugged the Cam Angle Sensor and it started and ran fine...
-
If a Crank or Cam angle Sensor were to be not hooked up properly somehow, would that disable spark or fuel? im guessing fuel.. as you wouldn't want to keep cranking and fill the cylinders up with fuel.??
-
Yes the PDF you linked helped me last night. Was hoping that I had the same issue as SIRREX. Swapped pins 14 and 5 around which I think gave the ECU power as we are getting the CEL on IGN on and when Cranking it disappears. Problem I think is no spark. Have Fuel Pump wired to IGN On, Can smell fuel but Im not ruling out that the injectors are not getting a Signal from the ECU. Checked the voltage to the Sensors, they all getting the correct voltage. Coils and Injectors have a Constant 12v+ when IGN on. Seems like ive got the basics to start a motor covered. But spark is not happening. Will check again today after work..
-
Oldish thread, but I'm also doing this conversion right now with my mate, could anyone tell me if you need to wire in the self shut off control to get her fired up? I'm having trouble locating this pin on the ver7 ecu I have, people on other forums with merge guides saying its pin 6 from connector a134, the pinout I have though is saying its an A/C switch... And all the pinouts I find of the v7 Wrx ecu don't tell me anything about this shut off wire, I've been able to locate it from the v2 its going into using pinouts I have, runs to the main relay under the dash..
-
And I put oil in this time.... Sigh...
-
haha blew it up, not from drifting but forgot to put oil in it... doh.. got another one in there already to go..
-
My RWD WRX use to one wheel (R180 now), but that was because I wore the LSD out.. before it was worn it was Twining up nicely. Started Singling up, then eventually blew.
-
Who's Online 0 Members, 1 Anonymous, 130 Guests (See full list)
- There are no registered users currently online
Dented sump question
in Engine Related
Posted
Hi all just doing a engine swap right this moment on my car and noticed a rather large dent in the sump of the replacement motor, does anyone know if this will be ok or how far up the pickup is from the bottom of the sump. I would replace it now but I'm strapped for time using my mates garage. I did a quick Google and others have been ok, but I'm not sure how large their dent is compared to mine, anyone had a dent in their sump that looks as bad as this? Here is some pics..