2000 legacy b4
-
Posts
206 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Events
Store
Posts posted by 2000 legacy b4
-
-
Was just trying to sell the car too ahaha I wanted a STI :\'(
-
Lol oh shit
I bet the previous owners didn\'t service it and ran it on 91 :
found lots of kids stuff in it when I brought it haha so guessing a family owned it! -
my legacy has developed this knock when you rev it yet it isn\'t there on idle could be a piston knock maybe?
http://s1155.photobucket.com/user/94legacy/media/20131116_1129231_zps5cb71b95.mp4.html
-
Dw bro i\'ll do some chasing if I see it
-
Looks tidy man!
-
That\'s pretty shit aye bro, Hope he gets it back! Will keep an eye out round Aux
-
Nice bro
Well done! -
I have always removed the primary to take the manifold off, Haven\'t yet found a way that I don\'t have to ???
-
This is why it\'s all happening, secondary is just as bad, I\'m pretty sure this is causing:
-Harder/takes longer to start
-Low idle on start up
-Boost spikes
-Very poor fuel consumption
-Lack of power
-Pinging/Detonation under load at low revs
-Adding to VOD
-Slower spooling
And here\'s a Dimensions pic Haven\'t found yet but could have been handy:
My B4 and GT-B both had this particular shape, Pretty sure it\'s just how it is as I had the primary turbo off and tried to make it straight but it was molded like this, Good upgrade tho never the less.
-
I think mine is better now but yeah.. Still not that impressed by it.
-
I don\'t run the factory boost control, Brought a gfb atomic
-
-
I didn\'t solder them because I didn\'t know if it was going to work, But it is a good connection, Yeah white stripes are going to the ecu, I might go out soon and re check it with the above diagrams supplied.
-
-
Did you solder all joins or use easy splicers? Most likely bad connection or wiring fault. Also there is a small black reset button behind the controllers front panel.
Before I started I labeled all 9 wires at the ecu so I knew what was what then from there I did one at a time till it was all connected.
-
Just adding that in the wet tonight b]when it\'s switched off it would light up the wheels[/b] however if you turned it on you\'d have almost full traction.... I don\'t want traction control :L
I am skeptical of your B4 barking up 4 wheels
However relating to your sequential controller a) are you positive you hooked it up right
b) do you have a boost gauge and what does it say
c) are you really sure it\'s not just a placebo effect - it shouldn\'t have any change to the running of the car apart from the switchover point, that\'s it - it doesn\'t alter any MAF readings as far as I\'m aware
only possible thing I can think of is if it\'s "somehow" only half opening the exhaust valve or leaving the secondary BOV open
Bro. They are cheap tyres haha don\'t worry it can
I\'ll re check the wiring and try the reset button! -
Just adding that in the wet tonight when it\'s switched off it would light up the wheels however if you turned it on you\'d have almost full traction.... I don\'t want traction control :L
-
After installing it today i\'m abit disappointed as I found when it\'s turned off it pulls abit harder so to me this would mean that it isn\'t doing it\'s job right and costing me some power ??? It also doesn\'t really reduce the VOD that I can tell " which it why I brough it". I am sure there is only one way of wiring it up other wise it wont work haha so figure I\'ve got that part right. But raising the cross over point is working. Any one got any ideas ???
-
My one just seized in my old bg5 , I was at the redline when this happened tho
-
More than likely the crank gets fucked any way
-
The thing is even when the beb goes it doesn\'t matter if you drive it or if you don\'t the motor is still bothered and will still need a rebuild IMO
-
oh lol didn\'t even notice that!
-
It makes no sense to me, I\'d rather just leave it for some one else to do!
-
I bet the previous owners didn\'t service it and ran it on 91 :
found lots of kids stuff in it when I brought it haha so guessing a family owned it!
I\'ll re check the wiring and try the reset button!-
Who's Online 0 Members, 0 Anonymous, 40 Guests (See full list)
- There are no registered users currently online
High Pressure in Coolant system
in General Vehicle Discussion
Posted
blocked radiator could do this, try a new thermostat