resurrection.inc
-
Posts
726 -
Joined
Content Type
Profiles
Forums
Events
Store
Posts posted by resurrection.inc
-
-
Has anyone seen inside a 6s before???
Mine has like another board on top of mother board
Will upload a pic when i can
Also has a red a green led and some little turning nobs lol
-
Bumer 25 years in chch move to h town and now u fellas bring this out! Agghhhh!
Anyhow awsm news may need to b a road trip
-
Question
Have a v3 sti and running a 6s ecu.
Have just brought a chipped profec b ecu and wanting to plug it in tonight.
Can i just remove old one and plug in?
Anything to watch out for?
Reset anything?
Have now put ecu in.
Car runs really rough like its hunting for idle and is only running on like 3
Any ideas? Have opened both ecu and theyre completely different
-
ah yes i have had two of them and they both got stolen so i gave up
-
so its single turbo?
-
-
http://www.clubsub.org.nz/forum/index.php/topic,763.0.html
However, if it hasn't ever been taken off before, then there might be screws holding in the metal tray that the ashtray slides into. There will be 2 that point up on an angle at the front (get a stubby philips), and one at the rear (get a long philips)
Get all them and you should be right.
The one at rear doesnt need to be removed just leave that one in so the tray stays in place u can jus push down very slightly and surround will go over it
-
they are different yes
-
ive just replaced all my lines with 4mm vac line and i havent had any problems
-
with my ver5 when it was standard i had 16's i think we put the tire pressure down to 30 from memory i launched at around 5000rpm as i had a smaller turbo but i was racing a 10.8 second honda but i was still happy with my 13.1
It was at a honda drag day.
actually have a picture
The tires were key being Goodyear GT1's such an awesome tire
you got 13.1 out of a standard v5?
-
-
ok cool, thought this was going to be the outcome
but hey better to ask first then to butcher something really good
-
i have a v3 sti running a 6s ecu.
since these are not tuneable.
can i re wire in a v7 sti ecu? and if i can am i able to use all the standard sensors that i am running already with the v3.
would like to wire it in so i can then tune it. or reflash it.
any help and input much appreciated
-
If theyre there they must work ie have mirror in and ba able to use if mirror is broken remove the whole thing and your sweet
-
Ah ha cheers
-
Arnt v5/6 top feed not side feed?
-
I can confidently say that cable ties do not pass you for a pink sticker nor cert
-
Which part u after? I hav some stuff lying around
-
-
mine had cutout at 18
-
Righto after many an install (especially nissans for some reason) this is what i have found. Make sure the amp is not placed by any part of computer in boot if your going to screw amp to floor paneling screw it to mdf then screw that to floor ( no carpet in between) when finding a ground if you dont use spear tyre well use that point or a seat belt point. BUT u must sand paper the paint and crap off connection as much as possible and make it clean as u can. Use full length wiring rather than joins and always make sure ground and power wiring is as big as possible. I prefer to use 4 awg but then u get awsm amps made by reputable brands and they give you this tiny bloody hole to try and screw a massive wire into! Not cool!
-
Sitting at vehicle testing now jus asked the fella. Anything that alters the power output of car from oem more than 10% must have a lvv inspection done. Thus includes a wrx getting an sti turbo! If it changes the output by more tgan 10%
-
I hav my alignment printout if u want it pxt or emailed to ya
-
U can buy a harness for it but if i remember correctly directly under steeringwheel there is a 4 plug connection. Think its red white blue and yellow. Disconnect and put those four wires into timer
-
Who's Online 2 Members, 0 Anonymous, 280 Guests (See full list)
6s ecu....
in General Vehicle Discussion
Posted
Yea that b choice joker if we could . Hopefully it makes it tuneable??