[Cool Video Thread]

 

[Replacement Wideband sensor for AEM UEGO kit]

1 hour ago, Pappu1 said:

you are located in auckland ya?

 

yip

[Replacement Wideband sensor for AEM UEGO kit]

just inspect the plug on the sensor real good. sometimes you cant tell if the wire has broken off the pin cause its all waterproofed under the rubber grommets etc 

[Replacement Wideband sensor for AEM UEGO kit]

@Pappu1 Mine would go super lean and then creep rich over the period of about a minute after turning the ignition on. Turned out to be a bad earth.. the ground wire had come out of the plug. 

[Replacement Wideband sensor for AEM UEGO kit]

7 minutes ago, Pappu1 said:

 

 

do the "replacement" sensors work any good (worth the monies?

 

 

the AEM leaflet says does not need free air cal but is it worth a try at all?

mine reads ultra lean and then spikes rich and normal for a second then back to lean

No idea, i've never had to replace mine from the original that came with my AEM wideband.. but its the same part number as the one I got when I thought mine was dead. Bosch 0258017025

[Replacement Wideband sensor for AEM UEGO kit]

What do you consider well priced? I've got a brand new Bosch 0258017025 LSU 4.9 sitting here if you need one in a pinch. $135 

Otherwise something like this might be the treat https://www.amazon.com/Replacement-Replaces-0258017025-Compatible-Wideband/dp/B07L2S3JRG/ref=sr_1_4?keywords=Bosch+0258017025&qid=1551315909&s=gateway&sr=8-4

[Wheel bearings!]

Id suggest so, just not sure what else it would be.. its the easiest thing to change too. Getting stuck into diff bearings is no fun and its also less likely than a wheel bearing 

[Wheel bearings!]

From my experience wheel bearings have to be pretty shagged to get noticeable movement when working the wheel by hand. Also often its the opposite side than it sounds like 

[Wheel bearings!]

Whats the milage, one of mine went at 120,000 and so I just did both. Mine sounded pretty metallic and rumbly.. 

[Wheel bearings!]

33 minutes ago, iludez said:

2 hours ago, A_J_T said:

easy to do if you buy the whole hub and bearing assembly, just did both my wagon front bearings. Its in my thread if you want to see photos of things apart. I got my bearings from SubTech in Penrose 

So I'd need to buy both hub and hub carriers?

this 

 

[Wheel bearings!]

easy to do if you buy the whole hub and bearing assembly, just did both my wagon front bearings. Its in my thread if you want to see photos of things apart. I got my bearings from SubTech in Penrose 

[Wheel Cleaning]

I find this guy fascinating to watch. Products he uses may not be available in NZ but his method is something pretty hectic haha 

 

 

[Legacy 2001 remap rev c model]

 

[Legacy 2001 remap rev c model]

If its 2001 I think you mean Rev-D in which case you are in luck. If its a Rev-C there is no remaping going to happen. 

 

@Pappu1 Would be your best bet 

[Clutch slipping]

 

4 minutes ago, StrokedEJ said:

Tried to avoid that cause it will blow my box to peices haha
 

isn't that a given with the power you are talking?

[Takata airbags recall]

@BMCracer I think its passed the point of giving them a chance to resolve it. That kind of damage simply shouldn't happen. There are a lot of us needing airbag recall work done so naming the shop as a precautionary measure for us would be awesome. We all understand that you are specifically warning us about Airbag recall work and not blanket stating that the shop is useless.. Its less shaming them and simply making them accountable for the poor workmanship you experienced. Sounds like they need to have a chat to their lads to make them more mindful.. some people simply dont think. 

[our Guide To Twin Turbo]

Just single Turbo it Bruv 

[Impreza EZ30 Swap]

56 minutes ago, pl0x said:

1st gen shouldn't even be considered a ez30 

thats offensive haha 

[Dyno run]

2 hours ago, Individualities said:

 

Still highly unlikely then (cancer is a F*****G ass hole). If I do make a race down (literally), I'll just be there for the food and hangs. Not fussed about getting my car on the dyno. Already know roughly what it puts down from the post I made in Dyno Leaderboard.

Sorry to hear that mate. Our family has been on that same journey like many and I found that although its a S*** situation it brought everyone closer. Hoping for the best outcome for you and your Family. Regardless of If you make it or not I look forward to meeting you 

[Dyno run]

1 hour ago, Dairusire said:

As far as calling it a ClubSUB event, it's obviously a no brainer

 

I can bring the banner stickers, small stickers etc. 

So your committee is all behind it  

 

Also, I'm in. If i've got the RA running by then, I'll tow the RA using the legacy

Cheers mate, sounds good... also if the RA makes it that will be a nice touch. lots on here have heard about the mythical being 

15 minutes ago, Individualities said:

Unfortunately I'm only gonna have to register myself as interested now; and if I do make it down, it'll be last minute.

Stuff going on in the family (health) that needs all the spare time I can muster at the moment.

Currently looking at making it happen next year late Jan early to mid Feb so hopefully that works for you 

[Dyno run]

Good on ya mate. I'll get a google sheet up for those that are keen to throw their details in. Just finalising things before we get to that point. 

 

Also @ADIKT I know you were largely involved with making the last one of these happen. Do we have ClubSUBs approval and support behind this etc, anyhting the Club can do on the day to make it more of a happening thing 

 

[Dyno run]

Just keeping you lot in the loop, PBMS have given me the below offer. Just waiting to hear back from some other shops on pricing etc. 

 

Quote

 

We’ll throw a BBQ for you and will give each competitor some free merchandise.

Unmonitored power runs for $89 per car
Monitored power runs (AFR and knock) for $129 per car

 

 

 

 

[Dyno run]

56 minutes ago, Dairusire said:

No really. There shouldn't be prices bud.

Back at MegaMeet 2017 when PBMS didn't turn up as a sponsor, they said they'd throw us a free dyno day for ClubSub Members as a thank you.

Seriously! I think there's even a post somewhere about it on the forums.

Yea I get that, and possibly one day two years ago they did promise something.. and if that is something they want to honour then awesome.. and I will mention it to them.. But I also get that running a performance based business in NZ is not the easiest job.. and that most of us here can spare $80 to have a go on a dyno. It will cost y'all more than that just to fill your car with 98 on your way to the Dyno.. 

 

I'm also reaching out to other shops to get competitive pricing.. you would hope PBMS as our sponsor can do something special for us. 

1 hour ago, Dre said:

Hopefully when the weather gets colder.

Nah, do it in the heat of summer.. if the car holds together and makes good power it only gets better in winter. 

[Dyno run]

Update: 

 

Been in touch with PBMS.. further details to come. Currently looking at something early next year as most people are super busy with business this time "Including myself". When I have more info on prices etc I'll start a dedicated thread with a poll to opt in and what not. 

 

Cheers

[Dyno run]

6 hours ago, PBMS said:

We love to support CS - you are our favourite club after all.

 

Make sure you keep in contact - email is best - [email protected], however feel free to give us a buzz at any time on 09 238 5732.

 

Cheers, Pat

Hi Pat, 

 

Good to hear from you and see you on the forum. I did send an email via the form on your website, but I’ll try flicking it through to that address and hopefully we can get something sorted. 

 

Cheers,

Aidin