Andy_Mac

Maybe on DOBC.

Yea that'll work.

Good find, I'd tried to find a substitute PN but none of them were available anywhere, but yea a wrecker trans is possibly a better way to go

@B4 2000 Gonna put spacers on them at all? I've always liked those ones besides the terrible factory offset

That or failing some form of quality control. I've purchased a few things as tests that look identical as other ones I've already had besides casting damage etc

You'll probably have better luck asking on one of the Facebook groups, besides @B4Gordon I don't think many of us have had much to do with 5th gens

I've got a mint condition black grimmspeed one I'll be parting ways with very shortly since it doesn't work with reverse manifold

May have found the cause of the mystery front end clunk that started recently ? @B4 2000 What's with the odd comp cover rotation? Is it going to have a 90 welded straight on it going forwards?

Cam tools are good to have. I got a set from TM in a hurry that'll surely be aliexpress quality but still work as intended without the massive markup from real brands That brake booster bracket could be a good way to go. I tried hacking up a cusco one to fit past my WG actuator but never quite worked

Hasn't it always needed a cert because of the brake pedal swap? It has been that way for at least as long as I can remember

Probably not worth it. Converting these to manual is a pretty complex process so only really worth doing on a limited edition one or low k’s on the body

Was anything properly damaged or just typical age related wear?

Weird, were they genuine ones or aftermarket? Genuine ones are usually reliable as hell

@MattyMo has the same style thing. Think it was the idoing version but I'm not super clued up on them other than that there are a couple of hardware variations out there with some being ok and others being rubbish. You're on FB aye? Join the hatch messenger group as there will be a bunch of guys there that have tried them. I prefer the tried and true solutions from mainstream brands for audio quality and response but they do have their benefits with running on the android platform

Couldn't tell you if there's any differences between the factory one but PBMS lists the PW TMIC as fitting both GR and VA which must mean they're close enough

Never heard of m45 but crowes and sas are pretty decent. Anyone somewhat specialising in Subaru’s should make it easier than a generic mechanic not familiar with any quirks these have. What was the cel you had? Or was that just a misfire on that one cylinder? What's the engine km and oil thickness used? It's not uncommon for the avcs curves to be a bit laggy if cold or the strainer is partially blocked.

Has he had spark plugs and coils out and test fired them to prove they are all working fine? I had a spare coil that would work for a few mins then fail for a few then come back again. Is he doing any logging to see what parameters spike/fall over when it does start to run rough? AVCS is a good thought as it'll behave weirder when the oil is cold if partially blocked then come right once thinned out If he has no luck just take it to SAS or Crowesport

Worth asking in the Legacy loonies FB page, not sure if anyone on here is particularly clued up on the H6’s

dunno about anything on this side of the world but the US had a heap with uppipe cats. Only ever a single scroll thing but a major headache for them as they had a tendency to break down and kill turbos.

Fan wise you’re probably best getting a second hand one from a wrecker like Subidoo spares. Shouldn’t cost too much since they aren’t exactly high demand items. the lock issue is a bit weird. By floppy I assume you mean you can pull the handles with no resistance like they would be when in the locked state?

Mine still isn’t reliable enough yet to be taking part in any track work

that’s what I was thinking. That’s not a decent check over and measure everything job in that amount of time, more of an autonomous replace the bare minimum. Even for someone who does it every day there’s quite a few hrs in removal and reinstall, but you could do that yourself and save a decent chunk of cash

From the looks of it that’s from a rev D Legacy. There were a few changes with the D and anything earlier as it was essentially V7 STI based rather than …5,6 based like older ones. From memory I believe it was cam/crank position stuff that is different but there was possibly more

doesn’t really apply to you since your top mount but I quite like the look of the setup they’ve gone for with these nozzles. Looks very OEM+ https://motoiq.com/project-gd-sti-adding-an-intercooler-sprayer-to-a-front-mount-intercooler/

Things have come a long way in the last few years though. They’re not all big ass cores jammed into tiny housings to give disappointing results anymore. I was reading his article about these precision ones a while back and they look pretty decent and shouldn’t be too hard to fit. Slightly limited with intake sizing and whatnot but it’s a decent improvement. But in reality if you’re aiming for 500whp rotated does open the door to far more options that ‘should’ work better https://motoiq.com/project-gd-sti-installing-an-upgraded-precision-ball-bearing-drop-in-turbo-and-larger-injector-dynamics-injectors/